#
# $Id: README.MatrixOrbital,v 1.2 2000/03/22 07:33:50 reinelt Exp $
#

This is the README file for the MatrixOrbital display driver for lcd4linux

This driver supports the serial interface alphanumeric display modules by
Matrix Orbital Corporation (http://www.matrixorbital.com).

I could only test it with the LCD2041 model, but I think every other (LCD) model 
should work. These displays are supported:

  LCD0821: 2 lines by  8 characters
  LCD1621: 2 lines by 16 characters
  LCD2021: 2 lines by 20 characters
  LCD2041: 4 lines by 20 characters (tested)
  LCD4021: 2 lines by 40 characters

I could not test the vacuum fluorescent display models, but I think they should work, too.
There are no entries for this models in the driver table (at the bottom of MatrixOrbital.c),
but they could be easily added.

The displays come with an RS-232 and an I2C interface. The driver supports the RS-232 interface
only (because I have no idea how to find the I2C bus on my motherboard). 

Power can be applied either via an external DC power supply, a modified floppy power connector
(be aware that you can destroy your display if you get the pins wrong!) or via the RI (ring) 
signal of the RS-232 port. I choosed the latter, and modified a serial card so that it supplies 
+5V from the ISA bus to this pin (again, be aware that this is dangerous if you connect any other 
serial device to this modified port).

The driver supports vertical, horizontal and split bars (two independent bars in one line),
all bar types can be used simultanously. As the displays only have 8 user-defined characters,
the needed characters to display all the bars must be reduced to 8. This is done by replacing
characters with similar ones. To reduce flicker, a character which is displayed at the moment,
will not be redefined, even if it's not used in this run. Only if the character compaction 
fails, this characters will be redefined, too.

The displays have a GPO (general purpose output), where you can connect a LED or something. 
The driver supports controlling this GPO, but this function is unused by now.


Configuration:

The driver needs/supports the following entries in lcd4linux.conf:

Display: a valid Matrix Orbital Display name (e.g. "LCD2041")
Port: serial device the display is attached to (e.g. /dev/ttyS2)
Speed: the baud rate from the display (configured via jumpers) must match 
       this value. Possible values are 1200, 2400, 9600 and 19200
Contrast: sets the LCD display contrast to a level between 0 (light) 
          and 256 (dark). Default value: 160

showmsg=1&amp;follow=1'>dvb-c</a>/<a href='/dtv-scan-tables.git/log/dvb-c/ch-interGGA?id=43895629e8fc3f843bdc1f08f719da75ec2ef3c6&amp;showmsg=1&amp;follow=1'>ch-interGGA</a> (<a href='/dtv-scan-tables.git/log/dvb-c/ch-interGGA?id=43895629e8fc3f843bdc1f08f719da75ec2ef3c6&amp;showmsg=1'>unfollow</a>)</div><div class='content'><table class='list nowrap'><tr class='nohover'><th class='left'>Age</th><th class='left'>Commit message (<a href='/dtv-scan-tables.git/log/dvb-c/ch-interGGA?id=43895629e8fc3f843bdc1f08f719da75ec2ef3c6&amp;follow=1'>Collapse</a>)</th><th class='left'>Author</th><th class='left'>Files</th><th class='left'>Lines</th></tr>
<tr class='logheader'><td><span title='2016-05-28 17:28:23 -0300'>2016-05-28</span></td><td class='logsubject'><a href='/dtv-scan-tables.git/commit/dvb-t/pl-Szczecin?id=90b412717bba962083a14ea7056d4c0bdd2b2613&amp;follow=1'>dvb-t/pl-Szczecin: Fix table</a></td><td>Mauro Carvalho Chehab</td><td>1</td><td><span class='deletions'>-30</span>/<span class='insertions'>+30</span></td></tr>
<tr class='nohover-highlight'><td/><td colspan='5' class='logmsg'>
Instead of tabs, it was using a "&lt;------&gt;". That break
parsers.

Signed-off-by: Mauro Carvalho Chehab &lt;mchehab@osg.samsung.com&gt;


</td></tr>
<tr class='logheader'><td><span title='2016-05-28 16:59:29 -0300'>2016-05-28</span></td><td class='logsubject'><a href='/dtv-scan-tables.git/commit/dvb-t/ca-AB-Calgary?id=7096892c9675f48fe63b01a9cdce50838cbc595e&amp;follow=1'>ca-AB-Calgary: move the newer version to atsc</a></td><td>Mauro Carvalho Chehab</td><td>2</td><td><span class='deletions'>-49</span>/<span class='insertions'>+14</span></td></tr>
<tr class='nohover-highlight'><td/><td colspan='5' class='logmsg'>
This file is an ATSC standard file, and not DVB-T. Replace
the legacy file with the newer one.

Signed-off-by: Mauro Carvalho Chehab &lt;mchehab@osg.samsung.com&gt;


</td></tr>
<tr class='logheader'><td><span title='2016-05-09 18:42:32 -0300'>2016-05-09</span></td><td class='logsubject'><a href='/dtv-scan-tables.git/commit/dvb-s/Astra-28.2E?id=e56800218f88cb777577083161975a3078ac0bf7&amp;follow=1'>Errors in scan file</a></td><td>Bob Goddard</td><td>1</td><td><span class='deletions'>-0</span>/<span class='insertions'>+21</span></td></tr>
<tr class='nohover-highlight'><td/><td colspan='5' class='logmsg'>
I posted an email with a patch back on 04/02/2016 17:32 only to find that nothing has been done.

This patch, reproduced below adds 2 new transponders to Astra 28.2E and removes a trailing space. This trailing spaces causes dvbv5-scan to segfault.

Why has this not been actioned and why was my email address banned? Is this a close community that tells people to f-off?

dvb-s/Astra-28.2E | 27 ++++++++++++++++++++++++---

Signed-off-by: Mauro Carvalho Chehab &lt;mchehab@osg.samsung.com&gt;


</td></tr>
<tr class='logheader'><td><span title='2016-05-06 09:01:20 -0300'>2016-05-06</span></td><td class='logsubject'><a href='/dtv-scan-tables.git/commit/dvb-s/Astra-28.2E?id=138d406945fb110062214d30b73ed4c71f433691&amp;follow=1'>Update dvb-s/Astra-28E with new transponders and corrections</a></td><td>Bob Goddard</td><td>1</td><td><span class='deletions'>-3</span>/<span class='insertions'>+24</span></td></tr>
<tr class='nohover-highlight'><td/><td colspan='5' class='logmsg'>
Update dvb-s/Astra-28.2E. 2 new transponders, corrected duplicate of
tp 92 in tp 93 and removed trailing space causing user tools segfault.

Signed-off-by: Bob Goddard &lt;linuxtv@1.linuxtv.bgcomp.co.uk&gt;


</td></tr>
<tr class='logheader'><td><span title='2016-05-01 14:00:44 -0300'>2016-05-01</span></td><td class='logsubject'><a href='/dtv-scan-tables.git/commit/isdb-t/br-to-Tocantinopolis?id=d89c2f2bf92af99e44428d2a8727bc1682a73909&amp;follow=1'>Add new Brazilian channel lists</a></td><td>Mauro Carvalho Chehab</td><td>305</td><td><span class='deletions'>-49</span>/<span class='insertions'>+17876</span></td></tr>
<tr class='nohover-highlight'><td/><td colspan='5' class='logmsg'>
Channels imported from portalbsd.com.br.

Signed-off-by: Mauro Carvalho Chehab &lt;mchehab@osg.samsung.com&gt;


</td></tr>
<tr class='logheader'><td><span title='2016-05-01 13:59:19 -0300'>2016-05-01</span></td><td class='logsubject'><a href='/dtv-scan-tables.git/commit/isdb-t/br-to-PortoNacional?id=e838e8af23ce2d4cbff1bcd4cafadf5500765278&amp;follow=1'>Update Brazilian channel lists to reflect latest status</a></td><td>Mauro Carvalho Chehab</td><td>990</td><td><span class='deletions'>-2504</span>/<span class='insertions'>+18744</span></td></tr>
<tr class='nohover-highlight'><td/><td colspan='5' class='logmsg'>
Syncrhonize with the latest tables at portalbsd.com.br.

Signed-off-by: Mauro Carvalho Chehab &lt;mchehab@osg.samsung.com&gt;


</td></tr>