Hi, this is a utility to setup IR control keymaps using the /proc/av7110_ir interface. just call # ./av7110_loadkeys [-i|--invert] [-a|--address ] keymapname.(rc5|rcmm) > /proc/av7110_ir If your IR receiver hardware inverts the signal, you should use the -i or --invert command line option. If you have two or more devices which use the same IR protocol, you should specify the -a or --address parameter. If the parameter is omitted, the driver listens to all device addresses. Some examples: Listen to *any* IR transmitter with uses the RC5 protocol: # ./av7110_loadkeys hauppauge.rc5 > /proc/av7110_ir Listen to RC5 transmitter with address 2: # ./av7110_loadkeys -a 2 hauppauge.rc5 > /proc/av7110_ir If you don't know the correct value for the -a parameter, take a look on the debug output of the driver (see below). Now you can test your hardware setup using evtest # ./evtest /dev/input/eventX where eventX is the IR input event device, usually event0 if you don't use USB mice or keyboards. ------------------------------------------------------------------------ Keymaps are in format: 0x00 KEY_0 0x01 KEY_1 0x42 KEY_HOME ------------------------------------------------------------------------ In order to write a new keymap you might want to see the raw key values in the kernel log. Use # insmod dvb-ttpci.o av7110_ir_debug=1 in order to enable some verbosity in the av7110_ir driver. Then watch the kernel log while pressing your remote control keys. When you don't see any messages in your kernel log you should check all electrical connections, the selected protocol (RC5 or RCMM?) and the inversion setting. You find a list of all linux input key identifiers in and "./input_fake.h". Please post new keymaps on the linux-dvb mailing list or send them to me . have fun! Holger tion value='grep'>log msg
AgeCommit message (Collapse)AuthorFilesLines
2008-09-14strftime_tz patch from Bernhard Wallemichael1-0/+11
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@894 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-09-08strftime_tz() plugin by Bernhard Wallemichael1-0/+25
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@893 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-09-03ULA200 driver by Bernhard Wallemichael7-2/+825
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@892 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-09-03indentmichael1-4/+4
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@891 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-08-31Increased the maximum bps to 230400, if defined in <termios.h>.sonic741-2/+7
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@890 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-08-27git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@889 ↵sonic741-18/+11
3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-08-27D4D updates by Svenmichael1-38/+60
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@888 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-08-03driver for 4D Systems serial displays by Sven Killigmichael9-45/+846
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@887 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-08-03signed/unsigned mismatchmichael1-3/+3
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@886 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-07-26added command functionsmichux1-2/+130
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@885 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-07-15added IRLCD driver by Jean-Philippe Civademichael10-5/+467
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@884 3ae390bd-cb1e-0410-b409-cd5a39f66f1f
2008-07-15'autoreconf -f -i' run & config.rpath addedmichael8-370/+1617
git-svn-id: https://ssl.bulix.org/svn/lcd4linux/trunk@883 3ae390bd-cb1e-0410-b409-cd5a39f66f1f